Simple, Rugged Quality

800-369-6233800-369-6233

Request for Quote

How Madden offers fast lead times on boiler blowdown equipment: Get blowdown separators in as little as 1-2 weeks

by Madden Manufacturing • May 19, 2017

Madden Manufacturing recently decided to invest time and resources into shortening lead times for our boiler bottom blowdown equipment product lines. The process of quoting, designing, and fabricating ASME certified pressure vessels for boiler blow off applications is meticulous. From the initial inquiry to date of shipment it is not uncommon for this process to take 4 months or more.

After weeks of going back and forth with the contractor to discuss the design and exactly what all is needed on the equipment, it can be frustrating to then wait 8-10 weeks for the fabrication stage of the unit(s).

Point being, from initial inquiry to ship date, blowdown equipment lead times vary greatly

Madden shortens the process as a whole, and consistently helps contractors, distributors, and end users work through the entire process as efficiently as possible.

Madden has an advantage with our extensive knowledge of boiler blowdown equipment which we have been producing for 65 years now. There are employees at Madden with over 25 years of experience designing boiler equipment; and this experience allows us to significantly cut down on the initial phase of design. After 65 years of producing boiler blowdown equipment, we have standard product lines and all the documentation needed to cover a high percentage of boiler blowdown applications. And when customization is needed, it is simple for Madden engineers to tweak our standard designs to fit your needs.

We are taking steps to shorten the submittal and approval process, as well as stocking more items to decrease fabrication times. Madden is eliminating bottlenecks in the process wherever we can.

Our first financial investment, was deciding to stock a boiler equipment lineMadden blowdown separator for boiler blowdown

It is costly to stock entire units, so we started with the blowdown separator to see if the option to dramatically decrease the lead time would take off with our distributors and end users.

Here’s why Madden can offer 1-2 week lead times on some of their more popular blowdown separator designs:

Madden blowdown separators models are pre-designed to be sized for intermittent bottom boiler blowdown based on the operating pressure of the boiler. The flash tank on the separator must be sized to handle the maximum amount of flash steam and water at any given second during the blowdown, and the vent sized specifically to handle the flash steam rate and drain to handle the remaining hot water. Our aftercoolers are sized based on the flash tank’s drain, with a coinciding automatic temperature regulating valve for the cooling water.

So,

This means, for our most popular designs, the BD230C44, BD230D45, and the BD230E55, we can keep BD230E55’s in stock at all times, and use them for emergency inquiries where the applications call for a BD230C44 or D45 by simply bushing down to the correct piping.

All of these units are sized to handle boilers operating up to 150 PSI. This means a BD230E55 with a 2” NPT inlet, and 5” 150# flanged vent and drain is a little excessive for a boiler operating at a lower pressure and blowing down with a smaller blow off pipe.

But for a minimal additional cost, we believe there is a great benefit for end users to bush their piping to fit a BD230E55 if it means they can have the unit on site in as little as a week!

Conclusion

The next time you are a part of hospital, prison, university, or food plant addition or new site build that involves a boiler room, or when you need an emergency replacement, seek out a Madden Manufacturing representative for pricing and availability.

Our small family owned manufacturing company has years of experience and is known for our responsive service and durable products. And now we’re focusing on increasing our production speeds.

Very few companies if any can offer emergency boiler blowdown separators in as little as a week without compromising the integrity and function of the blow off separator’s design.
 
Trust Madden’s simple, rugged quality. Find a sales rep near you or call (800) 369-6233/email: info@maddenmfg.com to start your inquiry. Thanks for reading, and have a great day!


 
 linked in share button  share on twitter icon  share on facebook icon
Please share this article with anyone you think may find it useful. Thank you!

Faster Lead Times than Neptune & Milton Roy

Madden Manufacturing is currently quoting lead times of:
  • Chemical Metering Pumps @ 1-2 weeks
  • Fully Assembled Chemical Feed Systems @ 3-6 weeks
  • Sample Coolers & Small Heat Exchangers @ < 1 week
  • Emergency/Rush pumps in 1-2 days!


Links

Subscribe to the RSS feed

Contact Us